EXTRACTED TEXT FROM: YY-B230C instructions.docx


Large electronic display  Instructions for the use of stage lighting equipment


Beam Lamp



                       







(Please read the instructions carefully and manage them properly before using the product)








In order to use this product correctly and safely, please read the instructions carefully before installing and using this product. This manual contains important installation and application information. Please strictly follow the instructions when installing and operating the product. At the same time, please keep this manual properly.
Our company's  beam lamp A new beautiful high-temperature-resistant metal body is used. This product is designed and produced in strict accordance with CE standards. It conforms to the international standard DMX512 signal protocol. It can be used alone or online. It has the characteristics of fast rotation, low noise and powerful functions. It is suitable for small and medium-sized concerts, theaters, studios, nightclubs, bars and other places.
Please carefully remove the packaging, check whether the product is damaged during transportation after the packaging is removed, and check whether the following contents are complete. 。       
          
Beam lamp--------1 instruction manual--------1 book
          Power cord--------1 signal line--------1                 
This product is in good condition before leaving the factory. In order to keep the product in good condition and ensure safe operation, users should follow the safety matters and the warnings in this manual.
Important:Damage caused by non-compliance with this manual is not covered by the warranty. The supplier is not responsible for the resulting product problems.
If the product has been exposed to an extremely unstable temperature environment (such as after transportation), please do not connect the product to the power supply immediately, because water droplets caused by temperature changes may damage the product. Please use it after the product returns to normal temperature. 
This product can Used in the AC110-240V voltage range, it is a product for indoor use. Please make sure that the voltage used is not higher than the range that the product can withstand!! The power plug must be plugged into a protective I.Kind of socket. The green or tea-blue conductor must be grounded.
Please check this product and power cord frequently. Make sure that the power cord is not folded or scratched, and is not connected to other cables! Special attention should be paid when connecting the power cord or related connection. Be sure to unplug the power supply when not using this product or before cleaning. 
Before using the product, please familiarize yourself with the operation function of the product. Please do not expose children or non-professionals to the product. Please do not shake this product. Do not use brute force when installing or operating products. Don't let non-professionals operate the product. Most of the damage is caused by unprofessional operation. 
The product is not equipped with relevant repair accessories. The maintenance and repair of products can only be carried out by professionals! 
Please do not change this product without authorization, otherwise it may damage the product, so the damage caused is not covered by the warranty. Moreover, unprofessional operation may lead to short circuit, burn or electric shock, etc.




Connection of DMX512 signal:
This lamp uses DMX512 signal control mode. The control signal of each lamp is in parallel. When connecting multiple lamp signals, it is best to use a double-core shielded cable. When connecting, each lamp is connected through the DMX signal jack (Canon seat) INPUT (input) and OUTPUT (output) on the lamp. The 3-core XLR plug terminal connecting the signal line of the lamp must correspond to each other. When connecting the lamp signal, it is recommended to use the DMX signal terminal. . It can be avoided that the control signal is damaged due to electrical noise. The DMX signal terminal connects a 120 ohm 1W resistor between the 2 pins and 3 pins of an XLR plug and connects it to the OUTPUT (output) jack of the last lamp.
Calculation method of the starting address code of the lamp:
The starting address code of the current lamp is equal to (the starting address code of the previous lamp) + (the number of channels of the lamp) Description:
1: The starting address value of the first lamp is A001. 
2: The basic number of channels of the controller should be greater than or equal to the total number of channels used by the lamp. 
3: Note: When using any controller, each lamp must have its own starting address code. If the starting address code of the first lamp is set to A001 and the number of lamp channels is 16CH; then the starting address code of the second lamp is set to A01. 7The starting address code of the third lamp is set to A03.3By analogy, (this setting also needs to be determined according to different consoles).






menu operation settings
Main menu
Sub-menu one
Function settings
Introduction to functions
DMX address

1-512

System settings
Show inverted 
Normal
.


Flip over


Language settings 
Chinese



English


Channel mode 
20CH


Operation mode 
DMX 



Sound-activated



Voluntary


Electronic lighting 
Shut



Open


The light bulb defaults 
Open_Close


Light bulb control 
Light up. 


The shortest path 
Open_Close


Horizontal reverse 
Shut



Open


Vertical and reverse 
Shut



Open


XY speed 
Low speed



Medium speed



Fast


Optocoupler detection 
Shut



Open


Return to the superior 
▲

Information inquiry 
Total time 
0-9999


Light bulb time 
0-9999


Time limit 
0-9999


Display software 
Vx001


XY software 
Vx001


Small motor software
Vx001


Return to the superior 
▲

Channel control 
Rotation of the color palette
0-255


Strobe 
0-255


Dim the light
0-255


Fixed pattern 
0-255


Prism 
0-255


Prism rotation.
0-255


Atomization 
0-255


Focusing. 
0-255


Horizontal rotation 
0-255


Horizontal fine-tuning 
0-255


Vertical rotation 
0-255


Vertical fine-tuning 
0-255


Reduce 
0-255


Light up 
0-255


XY speed 
0-255


Color disk speed 
0-255


Focusing speed 
0-255


Pattern speed 
0-255


Return to the superior
0-255

Working status 
XY communication 
Normal
Current status


Wrong


Small motor communication
Normal



Wrong


Focusing Hall 
Normal



Wrong


Color plate Hall 
Normal



Wrong


Pattern Hall 
Normal



Wrong


X-optical coupling 
Normal



Wrong


Y optocoupler 
Normal



Wrong


Fan speed. 
6500


Return to the superior 
▲

Auxiliary tools 
Check code 1 
0-9999


Total time 
Reset



Carry out


Light and cannon time 
Reset



Carry out


Restore the default 
Tacitly approve



Resume



Preserve


Horizontal rotation 
0-255
Zero initial position

Vertical rotation 
0-255


Focusing. 
0-255


Prism 1 (the prism) 
0-255


Prism 2 (Skiw) 
0-255


Prism rotation 1st 
0-255


Prism rotation 2 (two) 
0-255


Atomization 
0-255


Color combination 
0-255


Fixed pattern 
0-255


Color plate 
0-255


Strobes 
0-255


The midpoint of strobe 
0-255


The middle point of the first point 
0-255


The middle point of the two edges 
0-255


Midpoint of atomization 
0-255


Colorful points 
0-255


Return to the superior 
▲

Advanced settings 
Check code 2 
0-9999


Encryption of signals 
Open



Shut


DMX speed 
0-255


DMX data package 
0-255


DMX type 
0-055


DMX isolation 
0-65535
The smaller the value, the more stable the signal.

Drive board temperature
<110 degrees>
If it exceeds this range, it will show red.

Drive board 3.3V
3.0V - 3.6V
If it exceeds this range, it will show red.

Drive board 5.0V
4.5V - 5.5V
If it exceeds this range, it will show red.

Drive board 12V 
10.0V - 14.0V
If it exceeds this range, it will show red.

Drive board 36V 
20.0V - 42.0V
If it exceeds this range, it will show red.

X state 
Be static 



Turn 


X Hall 
Normal 



Wrong 
Show red

X-coupler phase 
0-3


X-coupler A 
40-160
The standard setting of 100 exceeds the required range to display red, but the red light on the panel does not alarm.

X-optical coupling B 
40-160
The standard setting of 100 exceeds the required range to display red, but the red light on the panel does not alarm.

X-optical coupling C 
40-160
The standard setting of 100 exceeds the required range to display red, but the red light on the panel does not alarm.

X-optical coupling D 
40-160
The standard setting of 100 exceeds the required range to display red, but the red light on the panel does not alarm.

X current angle 
000-540


X-driven state 
Normal 



Wrong 
Show red

Y state 
Be static 



Turn 


Y optocoupler 
Normal 



Wrong 
Show red

Y Hall 
Normal 



Wrong 
Show red

Y photocoupler phase 
0-3


Y optocoupler A 
40-160
If it exceeds this range, it will show red.

Y optocoupler B 
40-160
If it exceeds this range, it will show red.

Y optocoupler C 
40-160
If it exceeds this range, it will show red.

Y optocoupler D 
40-160
If it exceeds this range, it will show red.

Y current angle 
000-250


Y drive state 
Normal 



Wrong 
Show red

Return to the superior 
▲

Channel level. 
Rotation of the color palette 
0-255
Current DMX channel value

Strobe 
0-255


Dim the light 
0-255


Fixed pattern 
0-255


Prism 
0-255


Prism rotation.
0-255


Atomization 
0-255


Focusing. 
0-255


Horizontal rotation 
0-255


Horizontal fine-tuning 
0-255


Vertical rotation 
0-255


Vertical fine-tuning 
0-255


Reduce 
0-255


Light up 
0-288


XY speed 
0-255


Color disk speed 
0-255


Focusing speed 
0-255


Pattern speed 
0-255


Return to the superior 


Reduce 
Re-re reset all 
Cancel
Manual reset.


Carry out


XY reset 
Cancel



Carry out


Effect reset "
Cancel



Carry out


Return to the superior 


Exit the menu 




●20Channel table
Passageway
Name
Numerical value
Describe
CH1
CH1
Color
0-4
White light



5-9
White light + color 1



10-14
Color1



15-19
Color1+Color 2



20-24
Color2



25-29
Color2+Color3



30-34
Color3



35-39
Color3+Color4



40-44
Color4



45-49
Color4+Color5



50-54
Color5



55-59
Color5+Color6



60-64
Color6



65-69
Color6+Color7



70-74
Color7



75-79
Color7+Color8



80-84
Color8



85-89
Color8+ Color9 



90-94
Color9 



95-99
Color9+ Color 10 



100-104
Color10 



105-109
Color10+ Color 11



110-114
Color11



115-119
Color11+ Color 12



120-124
Color12 



125-129
Color12+ Color 13



130-134
Color13 



135-139
Color 13  + White light 



140-149
White light 



150-203
From fast to slow, forward flowing water



204-255
Reverse flow from slow to fast
CH2
CH2
Strobe
0-3
The light gate is closed.



4-103
Synchronous strobe



104-107
The light gate opens.



108-207
Divide the strobe equally.



208-212
The light gate opens.



213-225
Low-speed random strobe



226-238
Medium-speed random strobe



239-251
High-speed random strobe



252-255
The light gate opens.
CH3
CH3
Dim the light
0-255
0-100% dimming
CH4
CH4
Pattern
0-3
White light hole



4-7
Pattern 1



8-11
Pattern 2



12-15
Pattern 3



16-19
Pattern 4



20-23
Pattern 5



24-27
Pattern 6



28-31
Pattern 7



32-35
Pattern 8



36-39
Pattern 9



40-43
Pattern 10



44-47
Pattern 11



48-51
Pattern 12



52-55
Pattern13



56-59
Pattern14



60-63
Pattern15



64-67
Pattern16



68-71
Pattern17



72-111
Forward rotation-Fast-slow



112-115
Stop the running water



1116-155
Reverse rotation- Slow - Fast



156-161
Pattern1From slow to fast jitter



162-167
Pattern 2 shakes from slow to fast



168-173
Pattern 3 from slow to fast jitter



174-179
Pattern 4 from slow to fast jitter



180-185
Pattern5From slow to fast jitter



186-191
Pattern6From slow to fast jitter



192-197
Pattern7From slow to fast jitter



198-203
Pattern8From slow to fast jitter



204-209
Pattern9From slow to fast jitter



210-216
Pattern10From slow to fast jitter



217-222
Pattern11From slow to fast jitter



223-228
Pattern12From slow to fast jitter



229-234
Pattern13From slow to fast jitter



235-240
Pattern 14From slow to fast jitter



241-246
Pattern 15From slow to fast jitter



247-252
Pattern 16From slow to fast jitter



253-255
Pattern 17From slow to fast jitter
CH5
CH5
Prism
0-127
Remove the prism.



128-255
Prism cut in
CH6
CH6
Prism rotation.
0-127
0-400 degrees



128-190
From fast to slowTurn overFlowing water



191-192
Stop



193-255
From slow to fastFirst month of the lunar yearFlowing water





CH7
CH7
Reserve
0-255
No function
CH8
CH8
Colorful atomization
0-127
Not have



128-192
Insert atomization



193-255
Insert seven colors
CH9
CH9
Focus on
0-255
From far to near
CH10
CH10
X axis
0-255
0-540Linear measure
CH11
CH11
X-axis fine-tuning
0-255
UnknownAxis 16Bit fine-tuning channel
CH12
CH12
Y-axis
0-255
0-240 degrees
CH13
CH13
Y-axis fine-tuning
0-255
Y-axis 16Bit fine-tuning channel
CH14
CH14
Reserve
0-255
No function

CH15
CH15
Reduce
0-25
No function



26-76
Effect motor reset (5S)



77-127
Scanning motor reset (5S)



128-255
All motor reset (5S)

CH16
CH16
Reduce
0-9
No function



10-100
Extinguish the light bulb (5S)



101-255
Light bulb (5S)

CH17
XY speed
0-255
From fast to slow

CH18
Color disk speed
0-255
From fast to slow

CH19
Prism atomization speed
0-255
From fast to slow

CH20
Pattern disk speed
0-255
From fast to slow


Installation instructions for lamps and lanterns:
This lamp can be placed horizontally, hanging obliquely and upside down. You must pay attention to the installation method when hanging obliquely and upside down. Fixed installation of lamps and lanterns: Before positioning the lamps and lanterns, it is necessary to ensure the stability of the installation site. When reverting the hanging installation, it is necessary to ensure that the lamps and lanterns do not fall off the support frame. The safety rope should be used to pierce the support frame and the lamp handle to carry out auxiliary hanging to ensure safety. To prevent the lamp from falling and sliding, when the lamp is installed and debugged, pedestrians are prohibited from passing through the lower part. Regularly check whether the safety rope is worn and whether the hook screw is loose. If the hanging installation is unstable, the manufacturer shall not bear any responsibility for all the consequences caused by the falling of the lamp.


After-sales service
Attention! When the lamps leave the factory, they have undergone strict quality inspection and the packaging is intact. Please follow the instructions. Machine failures caused by human causes are not covered by the warranty. 
The company provides technical consultation to customers throughout their lives.
If the product fails and needs to be repaired, please show the product warranty card and fill in the relevant content truthfully. At the same time, we also hope that customers can give us feedback on the problems of the product in time, so that we can improve the product as soon as possible.







